Sucia Small Boat Rendezvous 2014 Day 1

My son Tim and I just got back from one of our favorite annual events - the Sucia Small Boat Rendezvous at Sucia Island State Park.

Like the last two years, we launched at Sandy Point Shores marina. 

The entrance to Sandy Point always makes me a bit apprehensive. The narrow and shallow entrance goes through a blind S-curve, which then opens to a shallow area with a 270 degree exposure to the vast Straight of Georgia.  During an ebb, the tidal current rushes through this S-curve like a river.  At low tide, there is barely enough room for one boat at a time to fit through the entrance.  You have to approach slowly and peek around the corner to see if there are any oncoming boats, then zip through if the coast is clear.

High tide was 8.9ft at 3:18 am
Low tide was -2.4ft at 11:02 am

We launched at 10:00am.  The worst possible time.  Right near the end of a minus tide with a swift outgoing current due to an 11.3 tidal change.

We should be Ok, I figured.  After all, Navigator only draws 6" of water.  In the back of my mind, I wondered if that was still true when fully loaded with two people and a weeks worth of camping gear.

As we approached the entrance, I idled the motor, double checked that the centerboard and rudder were fully up, and cautiously peered around the corner as I slowly crept toward the entrance.

The swift current immediately grabbed Ellie and swept us into the narrow channel. I instantly realized that the current was so strong that there would be no turning back. Id be using the motor to try to stay in the middle of the narrow channel and not much else. I shot a quick glance for oncoming boats, fortunately there were none, thank goodness. The channel looked too narrow for two boats to pass and there was no room to maneuver.  We were going through, no two ways about it.  Along both shorelines we could see about a dozen spectators, waiting to watch the next fool to try and shoot the rapids.  Up ahead the water looked "funny".  Ripply.  Whatd that mean?  Shallow?  Must be shallow.  How shallow?  I glanced over the side.  Gravel!  Crunch!

We were aground in the middle of the narrow channel with a swift current all around us.

Ok, now what?  Think.  Tides going out. We gotta get out of here or well be stuck here for hours, or until the next boat comes along and hits us.  Should I get out and push her off?  Probably a real bad idea.  The strong current would most likely rip the boat from my hands.

I looked over the stern.  The prop was still above ground.  "Ok, Tim, were gonna try and back our way out of this.  Hope it works".

I turned the motor around and gave it half throttle.  Nothing.  Gave it full throttle.  Our mighty 2hp outboard was giving it everything it had, but still nothing.  Still stuck.

"Tim, lets try shifting our weight around".  Ellie slowly started to move, then broke free!  We backed a safe distance away from the gravel bar and took a couple minutes to regain our composure and assess the situation.

Looking more closely at the water, we could see that it was shallow and ripply on the right, but on the left, closer to the opposite shore, it was clearly deeper.  But then it shot directly into a rocky breakwater.  "I think we can make it, Tim.  Well have to hug the left shore, then quickly zip over to the right at the last second to clear the rocks, then were home free".  Tim agreed, it looked doable.

So we checked again for oncoming boats, then cranked up the Honda to half throttle (full speed for Ellie) and rocketed through the channel.

Whew.  Made it!  Next time, we vowed, well pay closer attention to the tides.




After that ordeal, we were rewarded with many hours of  absolutely perfect sailing conditions.  We saw lots of dolphins.  One surfaced less than 20 from the boat.

We arrived at Sucia and set up camp.  This was our first opportunity to try out my new Anchor Buddy - a Fathers Day gift from my daughter Heather.  Thanks, Heather!  It works great.

Thats Cameron Im talking to.  Cameron and his son take a month off every summer and stop by Sucia for the rendezvous.  They sail a beautiful Wayfarer.

Jamie Orr, organizer of the event, always brings along a set of bagpipes, which he uses to greet arrivals, wish them farewell, or summon the group to various get-togethers like wine and cheese night, campfire gatherings, and the around the island race.  Boaters all around the island applaud using their horns.  In this video clip is Bob Ennenberg (Scram Pram "Duck"), Jamie Orr (Chebacco "Wayward Lass"), Paul Miller (Benford Friendship sloop "Friendship") and Dan Rogers (Balboa 16 "Ladybug").  Dan is organizing an 8-day Movable Messabout in Eastern Washington and Idaho that I am looking forward to attending.

Here, Jamie is summoning the group to celebrate the 11th anniversary of this Rendezvous, with a fine bottle of single malt scotch.

There is so much more to write about, but it is getting late.  I will write some more soon.  In the meantime, I hope you enjoy this most beautiful sunset.

Read More..

Sucia Small Boat Rendezvous 2014 Day 2

Saturday morning, after sleeping in a bit late, I fired up the Kelly Kettle while Tim did some writing.  Our Kelly Kettle, by the way, was a big hit.  Just about everyone who saw it was impressed with the speed it could boil water.  Several said they were going to get one for themselves.

There was no reason to hurry because we werent going anywhere.  This is what the perigee-syzygy  does to shallow Fossil Bay.

 

A -2.8 tide does provide an excellent opportunity to see parts of the island normally hidden from view.  Like Sucias treacherous reefs for example.

"Boaters should use caution when in the waters around this park. The word "sucia" is Spanish, meaning foul or dirty in a nautical sense. It refers to the numerous rocks and reefs which surround the island. These rocks and reefs have grounded and sunk numerous boats since European explorers first named the island in the 1790s. Boaters should check their charts frequently and pay particular attention to Clements Reef on the north shore of Sucia, as well as the entrances to Ewing Cove, Fox Cove, and Shallow Bay. There is a long reef which extends to the west of Little Sucia Island. Reefs also extend outward from Ev Henry Point, North and South Finger islands, and the Cluster Islands".

A couple years earlier I discovered what remained of one unfortunate boaters yacht, claimed by the reef at the entrance to Fox Cove.  This mornings low tide would be a great opportunity to see if the shipwreck was still there.

As I was about to set out for some shipwreck and fossil exploration, James McMullen appeared, looking for someone interested in going for a hike.  I told him about my plans and he agreed to join me.

We found the rusted, barnacle encrusted remains of the engine block and the boats windlass right where I remember seeing them years before.  They were straddled one on either side of the reef that obviously sank the boat.  We looked for evidence of exactly where the boat hit the reef but saw no obvious scratches or anything in the reef, but James found some other bits of metal nearby.

From there, we went on to explore the fossils on the southern cliffs of the point.  Every year they look a bit different as the cliffside slowly erodes away, replacing last years fossils with newly exposed ones.  Fossilized clams are by far the most common.  We didnt see anything else this year, but James discovered an unusually large one.

Later that afternoon, when the tide came in, Tim and I finally had an opportunity to explore Little Sucia Island.  This is a completely undeveloped little island just outside of Fox Cove.  It is surrounded by reefs and swift currents.  There is only one small patch of beach suitable to land a boat. The little bay on the North side looks inviting, but its a boulder field just below the surface. We anchored at the patch of beach and walked around the island.  The entire shoreline is covered with rocks and there are no trails, no campsites, and no indication that anyone has ever visited the island.  Quite nice, actually!

We returned to our campsite at Fossil Bay.  Tim went for another hike out to Ev Henry point.  As he came around a corner, he startled two bald eagles which took flight only a few feet from him. He said he could hear the wind whistling through their feathers and it scared the crap out of him!  Tim also came across a pile of white feathers, apparently the remains of a seagull eaten by something.  The park ranger we talked to later said it was probably a hawk.

Later that afternoon was Wine and Cheese night, a visit from my fishing buddy Ray, followed by an evening around the campfire with drinks and music.

Good times.

Read More..

Small Craft Weekend

A photo essay

When two great events happen at the same time, it can be hard to decide which way to go. But then, a busy summer schedule often trumps, which was the case for Doryman last weekend.

The closest event was a gathering of Coots on Fern Ridge Reservoir, in the beautiful Willamette Valley, near Eugene Oregon. So, I dropped by just in time Saturday to visit as the boats returned to the docks from a day on the water. This is my home team, so youve seen some of these boats before.

First up is Bob Larken in his Wavewatcher, a Bolger designed Birdwatcher. Bob is an electronics and computer wizard and his boat is tricked out with amazing stuff. He recently installed a remote controlled tiller pilot so he can steer from any location on the boat.

This is John Kohnens Redwing, Lazy Jack. He bought this boat recently from a fellow Coot and I think hes happy as a man can be.

Dennis McComber just finished this little runabout from a batteau.com plan. His son started the build and abandoned it. Dennis picked up where he left off and did a great job.

Cal Drake designed and built this Garvey and its the powerhouse of the group. I dont know how much horsepower it has, but its a lot. You might have noticed, some of the Coots are moving toward being a power squadron!

Not entirely. Hal Colvin brought his Pacific Pelican, Retta Ann. Ive sailed with Hal before in this boat. A very capable craft.

And Lou Brochetti came with his newly refurbished Devlin Egret. So new, she doesnt have a name yet.

Lou likes to tinker with a design as much as I do. He says the sail rig is a bit small and too far forward. Were looking for the upgrade soon Lou!

This is the beauty that caught my eye. The new caretakers of Richardson State Park and the custodians of these docks, own this boat.

Shes a Sam Rabl Picaroon and the story is, she was built in 1954 by Sam himself. Obviously the boat has undergone some extensive refitting and Id like to know more.

A planked Picaroon is rare. The examples Ive seen were all made from plywood.


A proper little yacht.

Speaking of proper yachts, north of here a few hundred miles was the first ever Pocket Yacht Palooza, in beautiful Port Townsend, Washington State. This new event was organized by the Port Townsend Pocket Yachters, co-sponsored by the Small Craft Skills Academy and Northwest Maritime Center, and held May 19 at the NWMC.



Marty Loken worked hard to make this inaugural event a success. Give the man a hand!

Photos can be found on the Packet Yachters website and additional information is provided by Joel Bergen on his Navigator site.

Watch for this one next year.



Heres a teaser from last Saturday, sent in by our friend Brandon.......

Pocket Yacht Palooza 2012

Photos by Brandon Ford

Read More..

The Rewards of Small Boats

My good friend Larry Cheek has written an excellent lead piece entitled "The Rewards of Small Boats" published on Opening Day of the Boating season, in the Seattle Times Pacific NW Magazine. Larry, as you may know, is the author of "The Year of the Boat", which is one of my favorite books (especially chapter 14) <grin>

Read More..

Pull and be Damned Small Boat Messabout

This weekends messabout is one that Ive been looking forward to for quite some time.  Im really excited.  Its called Pull and be Damned and it will be held at Seafarers Memorial Park in Anacortes, WA.


Looking over the posts on the Woodenboat forum, it looks like there will be an impressive selection of drop-dead gorgeous sail and oar boats to drool over.  There will be a potluck bar-b-que, and an optional overnight campout on nearby Saddlebag island.

The event is organized by legendary sail and oarsman James McMullen.  Im looking forward to hearing firsthand about his recent epic capsize off Port Townsend.

Hopefully the weather will hold out because I plan on taking lots of photos and videos!

Read More..

Cedar Key Small Boat Meet 2012

The month of May, in Florida, can be absolutely perfect for a small boat rendezvous. And it appears last weekend was just that.

For us who could not attend the Cedar Key Small Boat Meet, in Cedar Key Florida, here is a link to some photos from Lenna Young Andrews (AKA creativelenna).

And a link to another fine set of photos from catboat willy.


How about all those people standing knee deep in the water in May? No wonder so many folks show up for this event!





Photo of Bufflehead by Dave Lucas.

Read More..

Small Boat Saturday at Cama Beach State Park

Saturday October 15 was Small Boat Saturday at Cama Beach State Park on  Camano Island, WA.
This free end-of-season gathering had small boats on display both on land and in the water plus skills demonstrations and talks led by professionals. The event was hosted by Seattles Center for Wooden Boats and the Puget Sound chapter of the Traditional Small Craft Association.

We launched our boats at Camano Island State Park at 11:00 and had a terrific, but short, two mile sail North to Cama beach.  The 10 mph winds and the tide were against us, but the sun was pleasantly warm for a mid October day. So enjoyable that I began to wish the sail was much longer than only two miles!

I arrived at Cama Beach less than an hour later set anchor.

Lately, on the jwbuilders forum, there has been some discussion about how to do a clothesline anchoring system. There are several ways to do it. I do it the simple way, which goes like this:
1) Tie one end of the anchor line to the bow cleat.
2) Run the anchor line through a ring on the end of the anchor chain.
3) Tie the other end of the anchor line to the stern cleat.
4) Drop the anchor a bit offshore.
5) Move the boat closer to shore, to knee deep water.
6) Step out, grab the shore anchor and the anchor line loop and wade ashore.
7) Place the shore anchor on the beach and tie the anchor line to it as shown below.
8) To reel the boat in and out, untie, pull one side of the anchor line loop or the other, and retie.

Clothesline Anchor Caught on Tape!

Notes: Tie the anchor line to your shore anchor.  That way, if your other anchor were to slip or the anchor line were to break, you would not lose the boat because it would still be attached to the shore anchor.  Also, you need plenty of anchor line, at least twice as much since were forming a loop.

Long term subscribers to Small Craft Advisor magazine may recall a series of articles in 2007 and 2008 (issues 47, 49, 51 - 53) written by Jan Nicolaisen as he built a Core Sound 17.  This Core Sound was later purchased by Randy Jones, president of the Puget Sound chapter of the TSCA. Here you can see glimpse of Randys excellent seamanship skills.  Randy recently returned from a weeklong trip to the San Juan islands.  He sails his Core Sound everywhere without the aid of a motor - something I wish I could do. Well done Randy!

Off to look at the boats!
First to catch my eye was this adorable little lapstrake dinghy, traditionally built by the NW School of Wooden Boat Building. Well done!

The Center for Wooden Boats did a beautiful job on this Babson Island 14

Cama Beach was a 1930s era salmon fishing resort.  The historic fishing resort was a favorite summer getaway for families for more than 50 years.  A fleet of 40 or so boats was stored in the large boathouse after the building was completed around 1950, available for rental starting at $1.50/day. Cama Beach had the largest boat livery of the many resorts on Camano Island.  There were 8 different boat designs, built by a local shipwright who created simple functional lines, cedar planking with iron fittings and galvanized steel nails. By 1955, 14 rowboats, 24 kicker boats, and 4 inboards were available for recreation and fishing.

 

Under construction were these cedar strip canoes, built using a technique I had never seen before.

Many other boats on display, including some ever popular pelicans.

After the show, the run back to the boat launch was even quicker than the trip up. After retrieving the boats, we all headed out for pizza and beers. What better way to end such a wonderful day?

Read More..